11款羚羊加装大灯继电器
去年我的车大灯在路上突然熄灭了,经检查是组合开关接口烧糊了,直接用电线跨接焊锡处理。
![](http://club1.autoimg.cn/album/userphotos/2015/04/13/15/500_20440250-5169-ff1e-6b3c-n203agh9gl5e.jpg)
烧糊了组合开关接口
![](http://club1.autoimg.cn/album/userphotos/2015/04/13/15/500_20029840-5146-n8c9-dg17-n203af7kdn5n.jpg)
烧糊了组合开关接口,看来应该是羚羊的通病,看论坛很多车友有这个故障
![](http://club2.autoimg.cn/album/g20/M09/33/78/userphotos/2016/04/11/00/500_wKgFVFcKgjmAab9tABjhXb0JNQc009.jpg)
工具
![](http://club2.autoimg.cn/album/g19/M11/33/86/userphotos/2016/04/11/00/500_wKgFWFcKgwyAPr0lAAl8_QUQXoU365.jpg)
从拆车场拆的继电器很电线,5脚继电器上面没有接线图,不知道5只脚这么接
![](http://club2.autoimg.cn/album/g7/M01/50/50/userphotos/2016/04/11/00/500_wKgHzlcKgyyAdPlfABPZ6jKdHrI262.jpg)
直接把继电器拆开研究一下5只接线脚这么接
![](http://club2.autoimg.cn/album/g19/M03/33/85/userphotos/2016/04/11/00/500_wKgFWFcKgwiAZxEjABN02qTMUio871.jpg)
![](http://x.autoimg.cn/club/lazyload.png)
开始接线焊锡
![](http://x.autoimg.cn/club/lazyload.png)
先从正极加保险接线
![](http://x.autoimg.cn/club/lazyload.png)
接大灯接头。大灯插头找了2个陶瓷的
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
这是接车上电瓶的正极线
![](http://x.autoimg.cn/club/lazyload.png)
找了两条比较粗的电线作大灯的电源线
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
大灯插头的接地线
![](http://x.autoimg.cn/club/lazyload.png)
大灯插头焊锡
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
线路基本接好了,把线路用螺纹管用胶布包好
![](http://x.autoimg.cn/club/lazyload.png)
线路
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
拆了2个100W的大灯泡等审车时在换上,平时还是用65W,
![](http://x.autoimg.cn/club/lazyload.png)
先用电瓶试一下接线对不对。用一个大灯插头模拟原车大灯插头蓝色是远光灯正极,
![](http://x.autoimg.cn/club/lazyload.png)
白色线是近光灯正极
![](http://x.autoimg.cn/club/lazyload.png)
正常
![](http://x.autoimg.cn/club/lazyload.png)
线路制作好有几个月了一直没时间折腾。今天有空把它装在车上,保护原车组合开关和线路。
![](http://x.autoimg.cn/club/lazyload.png)
左边大灯插头接地线
![](http://x.autoimg.cn/club/lazyload.png)
继电器线路接电瓶正极
![](http://x.autoimg.cn/club/lazyload.png)
穿线路
![](http://x.autoimg.cn/club/lazyload.png)
继电器线路插头和原车大灯插头对接,没有破坏原车线路,如果继电器线路有问题,直接拔掉,还可以插上原车大灯插头。
![](http://x.autoimg.cn/club/lazyload.png)
右边拔掉原车插头,直接插上继电器线路的大灯插头
![](http://x.autoimg.cn/club/lazyload.png)
制作铁皮,继电器就安装在这里
![](http://x.autoimg.cn/club/lazyload.png)
试一下大灯的远光,近光。正常,,,,发个帖用了2个多小时,,,比修车还累,,,
分享到:
淄博车友1455893 2016/04/11 06:59:36 发表在 板凳
![](http://x.autoimg.cn/club/smiles/81.gif)
![](http://x.autoimg.cn/club/smiles/83.gif)
枣庄车友1350583 2016/04/11 10:21:16 发表在 4楼
不错~~~~~~~
没事瞎折腾![](//x.autoimg.cn/club/smiles/83.gif)
![](//x.autoimg.cn/club/smiles/13.gif)
![](http://x.autoimg.cn/club/smiles/83.gif)
![](http://x.autoimg.cn/club/smiles/13.gif)
我的也是摆角疝气灯,上次有装在车上试一下,很亮很亮。没有透镜怕对面司机受不了,就拆下来了还是用原车的。 迷你 透镜疝气灯泡!亮度怎么样?和摆角疝气灯比有什么不同![](//x.autoimg.cn/club/smiles/83.gif)
![](http://x.autoimg.cn/club/smiles/83.gif)
|