GM6装行李架了+雨眉也一起装了
![](http://club2.autoimg.cn/album/g3/M06/65/69/userphotos/2020/10/09/11/500_ChwFlV9_0jqAIWXuADdSiqG8pNs654.jpg)
进入正题前先纪念下油耗,这是开到最好的成绩。当然这是表显,实际还要加1.0~1.5个
![](http://club2.autoimg.cn/album/g3/M09/65/69/userphotos/2020/10/09/11/500_ChwFlV9_0juAPjuTADgwKb42gb4657.jpg)
所有东西到手,准备开始干活,左右是分开的颜色不要搞反了。
![](http://club2.autoimg.cn/album/g27/M01/46/F3/userphotos/2020/10/09/11/500_ChsEfF9_0juAAy5VADYMfaoLIik989.jpg)
配件送的撬棍,把原车的挡条撬开
![](http://club2.autoimg.cn/album/g3/M01/58/9F/userphotos/2020/10/09/11/500_ChsEkV9_0j2Ac6-QADck6XyCWFg677.jpg)
撬开后中间4个卡口取下来,两头的要保留。
![](http://club2.autoimg.cn/album/g27/M09/47/86/userphotos/2020/10/09/11/500_ChsEnV9_0j6AByRtADaSRflvdVU842.jpg)
![](http://club2.autoimg.cn/album/g27/M01/47/86/userphotos/2020/10/09/11/500_ChsEnV9_0j6ALCuAADTVKxmz3wQ482.jpg)
装卡子
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
从侧边滑进去
![](http://x.autoimg.cn/club/lazyload.png)
放上鸡米螺丝,顺时针拧紧就固定好了。
![](http://x.autoimg.cn/club/lazyload.png)
已固定,利用原来卡子的固定扣固定的。
![](http://x.autoimg.cn/club/lazyload.png)
用20mm开孔器打孔,打孔位置按照厂家的说明书位置打。
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
4个孔全部开好。
![](http://x.autoimg.cn/club/lazyload.png)
放上去试下,孔位刚好。
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
4个固定螺丝全部OK
![](http://x.autoimg.cn/club/lazyload.png)
上神器,铸工胶。
![](http://x.autoimg.cn/club/lazyload.png)
黏住他,这是我发明的。不是厂家标配。填满缝隙免得松脱,另外说下这个胶比铁还硬。推荐使用,不要用玻璃胶,软的没啥用。
![](http://x.autoimg.cn/club/lazyload.png)
打好胶再扣回黑色防水条,装上架子就OK啦。架子宁罗丝的过程就省了。
![](http://x.autoimg.cn/club/lazyload.png)
直接看效果把。
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
很牢固的,做大的作用就是挡水。这车顶面积打。下雨后开窗,行车时全部的谁都会沿车窗流进车里,已经被搞过几次了。每次都把座位搞湿了。
分享到:
|