清理驭胜进气管道
大胜已85000Km了,运气还不错买到高仿的驭胜了,发动机还没动过,二保后没过四儿子那,底盘传动都好,没发现生锈,特别是各种胶条下也没有,就是手刹锁线断,问四儿子修要500左右,我日抢了,老子自己来花10元买条油锯油门线自己弄好了,其他保养换机油换刹车片三滤也自已弄,反正钱不多就是时间多,上两周换了空冷管和清洗中冷,今天有空清洗进气管道。
![](http://club2.autoimg.cn/album/g14/M03/1F/F8/userphotos/2017/03/04/21/500_wKjByVi6whOAA-TjAALi7jxdQxo156.jpg)
皮带也差不多了,再跑万吧再换。
![](http://club2.autoimg.cn/album/g6/M0A/79/40/userphotos/2017/03/04/21/500_wKgH3Fi6wlKAIqd6AAKvA2uc6No606.jpg)
拆出来的样子,进气岐管拆出来要把那线弄开才拿得出来,那凸轮轴传感器的插头很难拆,要把传感器拆了才行
![](http://club2.autoimg.cn/album/g21/M12/FD/8D/userphotos/2017/03/04/21/500_wKgFVVi6wuaAeNkrAAT4PTS1cXc968.jpg)
我操全是油泥,进气道都变小了
![](http://club2.autoimg.cn/album/g21/M0F/02/52/userphotos/2017/03/04/21/500_wKgFWli6wxmAD_XKAAPkbz0U9Xg292.jpg)
近看
![](http://club2.autoimg.cn/album/g16/M09/21/35/userphotos/2017/03/04/21/500_wKjBx1i6wy6Af3T_AAOwwFC9Pyc890.jpg)
![](http://club2.autoimg.cn/album/g4/M0D/21/99/userphotos/2017/03/04/21/500_wKjB01i6wz2AIbSAAAV71I3Vl_E195.jpg)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
清洗干净后的样子
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
进气岐管好多碳粉和油
![](http://x.autoimg.cn/club/lazyload.png)
都变小了
![](http://x.autoimg.cn/club/lazyload.png)
清洗干净后
![](http://x.autoimg.cn/club/lazyload.png)
花了3瓶清洗剂一瓶汽油,一天时间
![](http://x.autoimg.cn/club/lazyload.png)
弄干就可装车了。
分享到:
|