是我的330IM,不是你的!
嗯,今天是2017年7月21日,我提车5个月了,车子实在西安提的,当时我们这边没有车,我说定一辆,结果告诉我说没有配额,定不上,无奈全国找车,最终在西安昌宝宝马找到了,哈哈,还没下线,我就订上了,2月份就把车开回家喽。5个月时间我跑了1.2W多公里了,。。。我自己都不知道怎么跑的。。。。。好吧,其实这个这个提车的帖子我应该很早就要交作业的,但是我想着,等我把车子收拾好了再交把。这一收拾就5个月过去了,现在车子也收拾的差不多了,嗯,其实也没动啥,就近十万元出去了,改装无底洞啊,而且我自己也是被改装店老板坑的不要不要的,好多车友和我买的东西是一样的,但是**我买的东西就是贵,唉~~心好累啊。其实我也不善言辞,但是在这里要感谢我们青海区域汽车之家版主“翼翔”给我找的好多师傅给我安装。感谢330全国群群主,哈哈哈,感谢的人太多!好了,不废话了,要开始上图了。。。。
![](http://club2.autoimg.cn/album/g18/M02/0A/88/userphotos/2017/07/21/09/500_wKgH2VlxWFyAWLetAAEqBsaa0-Q849.jpg)
这是我第一次在4S它,哈哈哈,当时的心情怎么说呢,说激动吧,其实也不激动,就是开心。哈哈哈
![](http://club2.autoimg.cn/album/g18/M12/0E/5C/userphotos/2017/07/21/09/500_wKjBxVlxWFyAfowAAAEvOprY5SI027.jpg)
![](http://club2.autoimg.cn/album/g19/M0C/E5/F8/userphotos/2017/07/21/09/500_wKgFU1lxWKyAbg3iAAXhy-qymDY692.jpg)
这是从4S出来后,去宾馆拿东西准备回家,路上1000公里路呢,哈哈,这么一看还是超好看的。
![](http://club2.autoimg.cn/album/g19/M0D/E5/F8/userphotos/2017/07/21/09/500_wKgFU1lxWKyAd6ULAAVyhAJZxew454.jpg)
请忽略保洁阿姨
![](http://club2.autoimg.cn/album/g19/M01/E5/F8/userphotos/2017/07/21/09/500_wKgFU1lxWKyAeoMSAAWujhvQ5Ik229.jpg)
霸气的车头,说真的,那时候MT版本的车子路上真挺少,现在好多好多。。。。
![](http://club2.autoimg.cn/album/g4/M09/13/76/userphotos/2017/07/21/09/500_wKgH2llxWTeAdFJAAAPWnjdwO4k311.jpg)
回家路上照的,因为新车,油耗挺好的,大晚上还下雪,一路大雪,LED大灯好散的感觉,看不清路,实际走的很慢很慢。
![](http://x.autoimg.cn/club/lazyload.png)
这个是车门上的冰,看着好膈应。。。。
![](http://x.autoimg.cn/club/lazyload.png)
到家了,我也忘记了我几点到的家,这是在加油站拍的,满车的冰,好心疼哦。。。
![](http://x.autoimg.cn/club/lazyload.png)
第一步,MP七件套。。。
![](http://x.autoimg.cn/club/lazyload.png)
右边副驾驶就没有替换的了。
![](http://x.autoimg.cn/club/lazyload.png)
左边MP七件套还是有的。
![](http://x.autoimg.cn/club/lazyload.png)
刹车到了,换刹车。。。
![](http://x.autoimg.cn/club/lazyload.png)
9660配合355的盘
![](http://x.autoimg.cn/club/lazyload.png)
9440配合330的盘
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
18寸的小脚,刚刚好
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
说句话刹车我是买的最贵的了,前6后4差2XXX到4W,后期还换了EBC黄皮,朋友都说买贵了,找改装店老板问所以然,最后给我退了4XXX,但是**,其实29XXX就能买下来,还有车友的更便宜。
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
EBC黄皮,换了之后真的逼AP原厂的要好,立马不一样
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
得切一下才可以装呢。
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
黄黄的真好看,虽然现在看不清了,哈哈哈
![](http://x.autoimg.cn/club/lazyload.png)
迟到的减震哈哈哈。
![](http://x.autoimg.cn/club/lazyload.png)
改减震,哈哈哈,
![](http://x.autoimg.cn/club/lazyload.png)
MP减震
![](http://x.autoimg.cn/club/lazyload.png)
MP弹簧
![](http://x.autoimg.cn/club/lazyload.png)
AN前唇后唇
![](http://x.autoimg.cn/club/lazyload.png)
拿到排气的时候激动啊!!
![](http://x.autoimg.cn/club/lazyload.png)
HSR三代配合原厂阀门排气
![](http://x.autoimg.cn/club/lazyload.png)
更换的蓝色安全带
![](http://x.autoimg.cn/club/lazyload.png)
附加的原厂排气阀门,,
![](http://x.autoimg.cn/club/lazyload.png)
开始拆车,
![](http://x.autoimg.cn/club/lazyload.png)
拆下来的原厂减震
![](http://x.autoimg.cn/club/lazyload.png)
MP减震压簧。
![](http://x.autoimg.cn/club/lazyload.png)
上车。。。
![](http://x.autoimg.cn/club/lazyload.png)
那个心情啊,哇塞,
![](http://x.autoimg.cn/club/lazyload.png)
嗯,明显的,MP减震要短一点
![](http://x.autoimg.cn/club/lazyload.png)
后部减震特写,
![](http://x.autoimg.cn/club/lazyload.png)
安装完成。。。
![](http://x.autoimg.cn/club/lazyload.png)
买的中尾端。
![](http://x.autoimg.cn/club/lazyload.png)
排气安装喽
![](http://x.autoimg.cn/club/lazyload.png)
后边。
![](http://x.autoimg.cn/club/lazyload.png)
阀门特写
![](http://x.autoimg.cn/club/lazyload.png)
好方便,不用接什么真空管了。
![](http://x.autoimg.cn/club/lazyload.png)
改完,洗车
![](http://x.autoimg.cn/club/lazyload.png)
哈哈
![](http://x.autoimg.cn/club/lazyload.png)
好低哦。
![](http://x.autoimg.cn/club/lazyload.png)
和好友320拍照,其实原厂轮毂也还好看。
![](http://x.autoimg.cn/club/lazyload.png)
发现AN的前唇吻合度不是特别好。
![](http://x.autoimg.cn/club/lazyload.png)
更换李子串
![](http://x.autoimg.cn/club/lazyload.png)
前后4个
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
更换拨片,这个拨片呢,本来不是这样的,是蓝色的,我觉得蓝色的不好看,就去找了家店弄了个水转印。。
![](http://x.autoimg.cn/club/lazyload.png)
拨片细节
![](http://x.autoimg.cn/club/lazyload.png)
套用的原厂的拨片总成,加了一个后盖
![](http://x.autoimg.cn/club/lazyload.png)
上车效果图
![](http://x.autoimg.cn/club/lazyload.png)
换的钥匙,也不贵。
![](http://x.autoimg.cn/club/lazyload.png)
刷的ID6.0界面,说真的,比ID5.0界面好看,实用
![](http://x.autoimg.cn/club/lazyload.png)
我的轮毂,哈哈哈,CSB锻造,
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
轮毂有一点让我**,量产数据只有8J 和 9 J 没有8.5 ,9.5 ,没办法,之后定制。价钱又上去了。。。
![](http://x.autoimg.cn/club/lazyload.png)
轮胎,东阳T1S性能胎,但我觉得不咋样。。。
![](http://x.autoimg.cn/club/lazyload.png)
准备装轮胎喽
![](http://x.autoimg.cn/club/lazyload.png)
包装的挺好的
![](http://x.autoimg.cn/club/lazyload.png)
轮胎,前面245.35.19后面265.35.19
![](http://x.autoimg.cn/club/lazyload.png)
为了不伤了漆面,师傅认真的很呢
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
245
![](http://x.autoimg.cn/club/lazyload.png)
265
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
![](http://x.autoimg.cn/club/lazyload.png)
顺带的,CSB钛合金锻造螺丝
![](http://x.autoimg.cn/club/lazyload.png)
弄好了,加油去哈哈哈,加油站拍的
![](http://x.autoimg.cn/club/lazyload.png)
后轮
![](http://x.autoimg.cn/club/lazyload.png)
前轮
![](http://x.autoimg.cn/club/lazyload.png)
忘记说了, 顺带了安装了RDC
![](http://x.autoimg.cn/club/lazyload.png)
哈哈哈,有这个东西还是挺好的。。
![](http://x.autoimg.cn/club/lazyload.png)
全景图,对了,雾灯去掉了,我觉得没有雾灯还是好看一点。
![](http://x.autoimg.cn/club/lazyload.png)
最后一步钥匙认证。。。
分享到:
Limmmmmmmmmmmmmmmmmm 2017/07/21 11:07:25 发表在 板凳
前排... 壕! 但是居然没有妹子 差评 !请你好好想想怎么把妹子加上来!
![](http://x.autoimg.cn/club/smiles/27.gif)
![](http://x.autoimg.cn/club/smiles/27.gif)
![](http://x.autoimg.cn/club/smiles/27.gif)
|